Create/Manage/Control OSDP Devices

osdpctl is a tool that uses libosdp to setup/manage/control osdp devices. It also serves as a starting point for those who intend to consume this library. It cannot be used directly in applications as most of the time a lot more product specific customizations are needed.

This tool brings in a concept called chanel to describe the communication between a CP and PD. Although OSDP defines this protocol to run on RS458 (serial), it is possible to run this over other mediums too. From a testing perspective, running on a unix IPC channel is very convenient. To know more about how this is achieved, look at channel_*.c files in this directory.

Configuration files

Since OSDP requires a lot of configuration information to setup a PD/CP, its not practical to pass all of them from the command line (I tried). So the tool uses a configuration file (ini format) to get the settings needed to configure the OSDP library (libosdp). This file determines if the service is to run as a CP or PD. You can read more about the configuration file and the various keys it can contain in the documentation section.

Some sample configuration files can be found inside the config/ directory.

Start / Stop a service

An OSDP service can be started by passing a suitable config file to osdpctl tool. You can pass the -f flag to fork the process to background and the -l flag to log output to a file or -q to disable logging. So to start a OSDP process as a daemon, you can do the following:

osdpctl pd-0.cfg start -f -l /tmp/pd-0.log

To stop a running service, you must pass the same configuration file that was used to start it.

osdpctl pd-0.cfg stop

Send control commands to a OSDP service

A command to be sent to a running CP/PD service must be of the following format. Some of these commands will in-turn be sent by the CP/PD device to its connected counterpart over OSDP as a command/event.

For instance, if you send a LED command to a CP instance specifying a correct PD offset, then that command is sent over to the relevant PD.

osdpctl <CONFIG> send <PD-OFFSET> <COMMANDS> [ARG1 ARG2 ...]

Here, PD-OFFSET is the offset number (starting with 0) of the PD in the config file CONFIG. In PD mode, since there is only one PD, this is always set as 0.

This section will only document the COMMANDS and their arguments. You must prefix osdpctl <CONFIG> send <PD-OFFSET> to each of these commands for them to actually get through.

CP commands

The following commands can be passed to a OSDP device that is setup as a CP. The PD to which these commands are being sent must have the capability of executing them. Refer to the PD capabilities document. for more details.

LED

This command is used to control LEDs in a PD. It is of the format: led <led_no> <color> <blink|static> <count|state>.

Examples:

led 0 red blink 5        # blink LED number 0 in red color for 5 times
led 1 amber blink 0      # blink LED number 1 in amber color forever
led 2 green static 1     # Turn on LED number 2 green color
led 1 blue static 0      # Turn off LED number 1 blue color

Buzzer

This command is used to control Buzzers in a PD. It is of the format: buzzer <blink|static> <count|state>.

Examples:

buzzer blink 0          # beep the buzzer forever
buzzer blink 5          # beep the buzzer 5 times
buzzer static 1         # turn off the buzzer
buzzer static 0         # turn on the buzzer

Output

This command is used to control LEDs in a PD. It is of the format: output <output_number> <state>.

Examples:

output 0 1        # Set output number 0 high
output 2 0        # Set output number 2 low

Text

This command is used to control the text that is displayed on the PD. It is of the format: text <string>.

Examples:

text 'Hello World'     # Set text "hello world" in display

Communication Params set

This command is used to set the communication parameters of a connected PD. It is of the format: comset <address> <baud_rate>.

Examples:

comset 12 115200  # Set PD address to 12 and baud rate to 115200